Voltage regulator Volter - 22пттм

PTTM-22 - Single-phase voltage regulator for an apartment or house a maximum power of 22kW, belongs to a new series of Volter PTTM, designed to provide a constant voltage of all kinds of electrical load from mains to poor voltage quality. This double conversion apparatus without accumulation of energy.
stabilizer provides:
- Output voltage stabilization at 220 +/- 0.5% when the input voltage from 130B to 320B frequency of 50 +/- 3 Hz.
- Cutout consumers with increasing input voltage over 330V to disconnect the input of the circuit breaker.
- Protection against short circuits and prolonged overloads at the output.
- mode (Transit) in an emergency.
- protection of consumers overvoltage mode (Transit) in the range of 260V +/- 5V voltage.
- protection Thermal stabilizer in the temperature range 75-85 ° C.
- Work around the load range from idle to maximum.
- normalized 4,5-7,5sek disconnecting consumers at short mains failure (no damage to the power switching power consumers)
-. The stabilizer does not introduce distortion in the output voltage waveform, and in the presence of its own distortions in the feed network reduces the content of higher harmonics (to reduce the heating of electric motors and transformers consumers, and to reduce their buzz).
- The stabilizer does not respond to gentle or to any sudden change in the input voltage, if they do not exceed the allowable operating range. For any smooth variations or races of the input voltage, output voltage remains unchanged. This is done in order to avoid the flashing bulbs and other lighting consumers.
- building energy consumption at idle no more 20Vatt.
Principle:
stabilizer provides no influence on the output voltage changes as the input voltage and surges and load changes. For this purpose it comprises a voltage source model with the mains frequency and a stable value which continuously compares the output voltage of the stabilizer. Due to this construction of the stabilizer, it does not react even at very sharp, almost instantaneous changes in the input voltage, and very quick to respond to any change in load. Just realized independent from the type of load, ie the stabilizer works equally active, capacitive and inductive load if the output current does not exceed the permissible output current.
In order to eliminate overheating and trip the thermal protection under severe operating conditions (full load, high ambient temperature) voltage regulator equipped with a forced cooling system, which is triggered by increasing the temperature in the device for more than 60 ° C. To eliminate the noise, two fans are used, operating at low speed.
During operation in mode (Stabilization) for emergency raising of the input voltage (over 330V) occurs the circuit breaker. Reclosing can only reset for the circuit breaker to the ON state. If the input voltage thus remains above 330V occur retrip that protects the load from overvoltage.
In case of accidental lowering of the input voltage (hereinafter, 105B), the controller turns off all power switches and de-energizes the load. By increasing the input voltage to the load connection 130B occurs automatically.
During operation in mode (Transit) at an input voltage of more than 260 +/- 5V stabilizer triggered automatic switch. Reclosing can only reset for the circuit breaker to the ON state. If the input voltage thus remains above 260 +/- 5V occur retrip that protects the load from overvoltage.
Before turning stabilizer, if it is stored or transported at temperatures below 0 ° C, it is necessary that it stood at room temperature of at least 5 hours

CHARACTERISTICS:.
Type - electronic stepless
phase - one phase
input voltages, V - 130-320
Nominal O . voltage, - 220 O
deviation. voltage from the nominal% - ± 0,5
Max. power output in kW - 22,0
O. power at the lower value Uin, kW - 13,0
O. Power at the upper level Uin, kW - 11.0
power consumption, W - 20
delay reclosing range from - 4.5-7.5
Cutout with decreasing input voltage. B - 105
Cutout with increasing input voltage. B - 330
Cutout in "transit" mode, B - 260 ± 5
current drawdown machine A - 100
Cooling - Forced
mounting method - mounted / floor
Dimensions, mm (height x width x depth) - 580 x 420 x 295
Weight, no more than - 48.0
protection class - IP20
Operating temperature environment, ° C 1 + ... + 40
Operating humidity,% 40 80 ... Seating
atmospheric pressure range, mm. Hg ... 630 800
Color - light gray
Warranty, months. 60